Share:
Parameter of Walk-In Environmental Test Chambers (general)
| Model | MWER-42000Y |
| Inner chamber sizeW×H×D(mm) | Non-standard |
| Exterior chamber sizeW×H×D(mm) | |
| Temperature range | 0℃；-20℃；-40℃；-60℃，-70℃～+70℃（+80℃） |
| Humidity range | 30% RH～95%RH |
| Temp.Humi fluctuation | ±0.3℃；±0.5%RH |
| Temp.Humi uniformity | ±3℃；±5%RH |
| Indication Resolution | Temperature:0.01 humidity:0.1%RH |
| Heat-up and Cool-down time | Heat-up:2℃/min(Average),cool-down time 1℃/min(Average) |
| Air circulation system | Centrifugal fan air circulation system |
| Heating system | SUS＃Stainless steel high-speed heater |
| Humidification system | Electrothermal steam humidification |
| Refrigeration system | Compressor + Finned evaporator + Air(Water) cooled condenser |
| Dehumidifying system | dew point dehumidification method |
| Controlling system | Touch screen controller+SSR+PID |
| Exterior chamber material | Cold-rolled plate + Powder coating |
| Interior chamber material | SUS＃304 Stainless steel |
| Insulation material | PU +fibergalss wool |
| components | Vacuum glass observation window |
| Test hole (50mm) | |
| Control status indicator | |
| Interior light | |
| Overheat protection circuit breaker | |
| Safety protection device | Humidification system overheat protection |
| Compressor overload protection | |
| Control system overload protection | |
| Overload indicator | |
| Phase sequence protection | |
| Water shortage protection | |
| High voltage and low voltage protection | |
| Over-temperature protection | |
| Water supply delay protection | |
| Fan overcurrent protection | |
| Power supply | AC 3Ψ380V 60/50Hz Power supply can be customized |
| Customization service | Non-standard or special requirements are all welcome |
Description of Walk in Stability Chamber in Pharmaceutical
Walk in stability test chamber is used to test the law of changes in raw materials or pharmaceutical preparations over time under the influence of specific temperature and humidity, to provide scientific basis for the production, packaging, storage, and transportation conditions of drugs, and to establish the validity period of drugs through experiments.
Drug stability tests include influencing factor tests, accelerated tests and long-term tests.
1. Factor tests：High temperature test (not exceeding 60C) and high humidity test (usually not exceeding 75%)
2. Accelerated tests：The samples are divided into three batches, which are observed for 6 months in the environment of 40℃±2℃/75%RH±5%RH and 25℃±2℃/60%RH±5%RH respectively, at 30℃ ±2℃/65%RH±5%RH Observe for 12 months in an environment .
3. Long-term tests: Observe in the environment of 25℃±2℃/60%RH±5%RH and 30℃±2℃/65%RH±5%RH for more than 12 months.
Parameter of Walk in stability chamber in pharmaceutical
| Model |
MWER-41000Y |
| Chamber Size | Non-standard |
| Temperature range |
20℃～80℃ |
| Humidity range | 50-75%RH |
| Temp.Humi fluctuation | ±0.3℃；±0.5%RH |
| Temp.Humi uniformity | ±3℃；±5%RH |
| Indication Resolution | Temperature:0.01 humidity:0.1%RH |
| Heat-up and Cool-down time | Heat-up:2℃/min(Average),cool-down time 1℃/min(Average) |
| Air circulation system | Centrifugal fan air circulation system |
| Heating system | SUS＃Stainless steel high-speed heater |
| Humidification system | Electrothermal steam humidification |
| Refrigeration system | Compressor + Finned evaporator + Air(Water) cooled condenser |
| Dehumidifying system | dew point dehumidification method |
| Controlling system | Touch screen controller+SSR+PID |
| Exterior chamber material | Cold-rolled plate + Powder coating |
| Interior chamber material | SUS＃304 Stainless steel |
| Insulation material | PU +fibergalss wool |
| components | Vacuum glass observation window |
| Test hole (50mm) | |
| Control status indicator | |
| Interior light | |
| Overheat protection circuit breaker | |
| Safety protection device | Humidification system overheat protection |
| Compressor overload protection | |
| Control system overload protection | |
| Overload indicator | |
| Phase sequence protection | |
| Water shortage protection | |
| High voltage and low voltage protection | |
| Over-temperature protection | |
| Water supply delay protection | |
| Fan overcurrent protection | |
| Power supply | AC 3Ψ380V 60/50Hz Power supply can be customized |
| Customization service | Non-standard or special requirements are all welcome |
Inquiry - Walk in Stability Chamber
